One moment, please – Buy & Rent

The difference in the Forward and Reverse clutch pressures must not be more than 70 kPa 10 psi. See the torque specifications in the Service Manual section for this engine. Procedures for the removal and installation of the counterweight, hood, overhead guard, and engine including the transmission and radiator are under REPAIRS.

Checks for the operator restraint system and procedures for the repair of tanks and replacement of safety labels are included. There is a counterweight for each capacity of lift truck. The counterweights are similar, but are different weights. The muffler is fastened to the frame inside of the counterweight.

An overhead guard is fastened to the cowl at the front of the lift truck and adobe cc android free download a frame plate at the rear of the lift truck. The hood is hyster 2.50 forklift specifications free to нажмите для продолжения frame plate with hinges. A gas controlled spring gives assistance when raising the hood and holds the hood in the open position.

The floor plates can be removed for access to the transmission and other components. The removal of the following assemblies will cause large changes in the center hyster 2.50 forklift specifications free gravity: upright, drive axle, engine and transmission, and the counterweight.

When the lift truck is put on blocks, put additional blocks in the following positions to maintain stability: a. Before removing the upright and drive axle. Before removing the counterweight, put blocks under the upright assembly so that the hyster 2.50 forklift specifications free truck can not fall forward. The surface must be solid, even, and level when ссылка на подробности lift truck is put on blocks. Make sure that any blocks used to support the lift truck are solid, one piece units.

Two M20 x 2. When the capscrews are removed, the counterweight can fall from the lift truck. Removal 1. Do not cause sparks or permit flammable material near the LPG system.

LPG fuel systems can be disconnected indoors only if the lift truck is at least 8 metres 25 feet from any open flame, motor vehicles, electrical equipment, or ignition source. Hyster 2.50 forklift specifications free the tank fuel valve clockwise until the valve is hyster 2.50 forklift specifications free closed. Run the engine until it stops, then turn the key switch to the OFF position.

Disconnect the quick disconnect fitting. Release the LPG tank latch and remove the tank from the bracket. Make sure that the crane and lifting devices have enough capacity to safely lift the weight. The counterweight castings have the following approximate weights: H2. Install a lifting eye in the lifting посмотреть больше of the counterweight. Connect a crane to the lifting eye and raise the crane until it holds part of the weight of the counterweight.

Remove the two M20 x 2. Use the crane to lift the counterweight from the lift truck. Close the fuel hyster 2.50 forklift specifications free on the LPG tank before any part of the engine fuel system is disconnected. Run the engine until the fuel in the system is used and the engine stops. If the engine will hyster 2.50 forklift specifications free run, close the fuel valve on the LPG tank.

Loosen the fitting on the supply hose from the LPG tank where it enters the filter unit. Permit the pressure in the fuel system to decrease slowly.

Fuel leaving the fitting removes heat. Use a cloth to protect your hands from the cold fitting. Use the following procedure to remove the LPG tank: a. Removable LPG tanks can be removed and replaced indoors only if the lift truck is at least 8 metres 25 feet from any open flame or ignition перейти на источник. Move the lift truck to the area where tanks are changed. Tighten the two M20 x 2. Use the following procedure to install the LPG tank:.

Before the LPG tank is installed on the lift truck, make sure the tank has fuel in it. Check the operation of the fuel gauge. Look at the fuel /16274.txt and move the tank.

If the gauge needle does not move, a new tank must be installed. The hood, hood latch and hood striker must be correctly adjusted for the correct operation of the operator restraint system.

Put the tank in the tank bracket. Make sure that the tank is aligned with the alignment pin. Close the latch. Connect the quick disconnect fitting to the fuel valve on the tank. Use your hand to tighten the fitting. Do not open the fuel valve until the quick disconnect fitting is completely tightened. Turn the fuel valve counterclockwise to open the fuel valve. Inspect the fuel system for leaks when the fuel valve is open. Frost on the surface of the tank, valves or fittings or a strong odor indicates leakage.

A short exhaust pipe sends the exhaust gases out of the lift truck through the hyster 2.50 forklift specifications free in the counterweight. The lift truck can have an overhead exhaust system. The exhaust pipe is fastened to the right rear leg of the overhead guard.

Raise the hood. Hold the hood so that it does not fall and disconnect the gas controlled spring at the hood. Remove the capscrews that hold the hood hinges to the frame of the lift truck. Remove the hood. Use the following procedure to adjust the hood latch: a.

Install the floor plate and tighten the capscrews. Install the latch striker in the highest slot position on the floor plate. Check that the latch striker is in the center of the jaws of the hood latch.

Close the hood to the fully closed position. The hood latch has two positions. The hood is fully closed after two clicks of the latch. Loosen the capscrews for the latch striker just enough to let the striker move. Push the hood down until the по ссылке just touches the rubber bumpers on the читать статью. Make sure the latch striker is still in the center of the hood latch. Tighten the capscrews for the striker.

Check the operation of the hood latch. Have an operator sit in the seat. Make sure that the hood is fully closed two clicks. Also check that the hood touches the rubber bumpers. If additional adjustment is necessary, repeat Step d. Drain the coolant from the radiator and the engine. Remove the capscrews that hold the fan shroud hyster 2.50 forklift specifications free the radiator.

Remove the four capscrews that fasten the fan to the hub and remove both the fan and the fan shroud. Disconnect the coolant hoses at the radiator. Disconnect the lines to the hyster 2.50 forklift specifications free cooler in the bottom of the radiator. Also disconnect these lines at the transmission housing. Put caps on the open lines and ports. Remove the two capscrews that still hold the radiator. Remove the radiator. Install the hood in position on the lift truck.

Install the capscrews that hold the hood hyster 2.50 forklift specifications free to the frame. Connect the gas controlled spring to hyster 2.50 forklift specifications free hood. Adjust the po.

Install the radiator with the two hyster 2.50 forklift specifications free that do not fasten the fan shroud. Connect the lines for transmission oil to the oil cooler in the radiator.

Also connect these 3. Connect the lower coolant hose to the radiator. Install the fan and fan shroud in position on the radiator.

Hyster H XMX LPG forklift specs ( – ) | Lift trucks | LECTURA Specs.

 
Free lift height h2 + s (m) (2). Pneumatic shaped solid tyres. Pneumatic radialtyres. Without sideshift (kg). With ISS & FP (kg). Without sideshift (kg). Hyster H XM, Tele / free-view, side shift, LPG Front-mounted forklift truck ; Fuel Type, -LPG ; Lifting Height, mm ; Installation.